1
我試圖接口LPC1769和MPU6050而我正在使用mcb1700.code.bundle.lpc1769.lpcxpresso庫。我正在使用LpcXpresso作爲IDE。接口問題LPC1769和MPU6050
按照MPU6050數據表中的規定，我爲讀取序列編碼，它只是第一次工作，如果我嘗試第二次讀取，它會返回零值。 （即復位後它只能工作一次）
我嘗試了很多可能的方式，沒有結果所以請給我一些解決方案來解決這個問題。
已編輯.. 我在下面顯示的代碼。讀取和burstRead代碼工作只有一次
i2c.c
#include "lpc17xx.h"
#include "type.h"
#include "i2c.h"
volatile uint32_t I2CMasterState[I2C_PORT_NUM] = {I2C_IDLE,I2C_IDLE,I2C_IDLE};
volatile uint32_t timeout[I2C_PORT_NUM] = {0, 0, 0};
volatile uint8_t I2CMasterBuffer[I2C_PORT_NUM][BUFSIZE];
volatile uint8_t I2CSlaveBuffer[I2C_PORT_NUM][BUFSIZE];
volatile uint32_t I2CCount[I2C_PORT_NUM] = {0, 0, 0};
volatile uint32_t I2CReadLength[I2C_PORT_NUM];
volatile uint32_t I2CWriteLength[I2C_PORT_NUM];
volatile uint32_t RdIndex0 = 0, RdIndex1 = 0, RdIndex2 = 0;
volatile uint32_t WrIndex0 = 0, WrIndex1 = 0, WrIndex2 = 0;
/*
From device to device, the I2C communication protocol may vary,
in the example below, the protocol uses repeated start to read data from or
write to the device:
For master read: the sequence is: STA,Addr(W),offset,RE-STA,Addr(r),data...STO
for master write: the sequence is: STA,Addr(W),offset,RE-STA,Addr(w),data...STO
Thus, in state 8, the address is always WRITE. in state 10, the address could
be READ or WRITE depending on the I2C command.
*/
/*****************************************************************************
** Function name: I2C_IRQHandler
**
** Descriptions: I2C interrupt handler, deal with master mode only.
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void I2C0_IRQHandler(void)
{
uint8_t StatValue;
timeout[0] = 0;
/* this handler deals with master read and master write only */
StatValue = LPC_I2C0->STAT;
switch (StatValue)
{
case 0x08: /* A Start condition is issued. */
WrIndex0 = 0;
LPC_I2C0->DAT = I2CMasterBuffer[0][WrIndex0++];
LPC_I2C0->CONCLR = (I2CONCLR_SIC | I2CONCLR_STAC);
break;
case 0x10: /* A repeated started is issued */
RdIndex0 = 0;
/* Send SLA with R bit set, */
LPC_I2C0->DAT = I2CMasterBuffer[0][WrIndex0++];
LPC_I2C0->CONCLR = (I2CONCLR_SIC | I2CONCLR_STAC);
break;
case 0x18: /* Regardless, it's a ACK */
if (I2CWriteLength[0] == 1)
{
LPC_I2C0->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[0] = I2C_NO_DATA;
}
else
{
LPC_I2C0->DAT = I2CMasterBuffer[0][WrIndex0++];
}
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
case 0x28: /* Data byte has been transmitted, regardless ACK or NACK */
if (WrIndex0 < I2CWriteLength[0])
{
LPC_I2C0->DAT = I2CMasterBuffer[0][WrIndex0++]; /* this should be the last one */
}
else
{
if (I2CReadLength[0] != 0)
{
LPC_I2C0->CONSET = I2CONSET_STA; /* Set Repeated-start flag */
}
else
{
LPC_I2C0->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[0] = I2C_OK;
}
}
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
case 0x30:
LPC_I2C0->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[0] = I2C_NACK_ON_DATA;
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
case 0x40: /* Master Receive, SLA_R has been sent */
if ((RdIndex0 + 1) < I2CReadLength[0])
{
/* Will go to State 0x50 */
LPC_I2C0->CONSET = I2CONSET_AA; /* assert ACK after data is received */
}
else
{
/* Will go to State 0x58 */
LPC_I2C0->CONCLR = I2CONCLR_AAC; /* assert NACK after data is received */
}
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
case 0x50: /* Data byte has been received, regardless following ACK or NACK */
I2CSlaveBuffer[0][RdIndex0++] = LPC_I2C0->DAT;
if ((RdIndex0 + 1) < I2CReadLength[0])
{
LPC_I2C0->CONSET = I2CONSET_AA; /* assert ACK after data is received */
}
else
{
LPC_I2C0->CONCLR = I2CONCLR_AAC; /* assert NACK on last byte */
}
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
case 0x58:
I2CSlaveBuffer[0][RdIndex0++] = LPC_I2C0->DAT;
I2CMasterState[0] = I2C_OK;
LPC_I2C0->CONSET = I2CONSET_STO; /* Set Stop flag */
LPC_I2C0->CONCLR = I2CONCLR_SIC; /* Clear SI flag */
break;
case 0x20: /* regardless, it's a NACK */
case 0x48:
LPC_I2C0->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[0] = I2C_NACK_ON_ADDRESS;
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
case 0x38: /* Arbitration lost, in this example, we don't
deal with multiple master situation */
default:
I2CMasterState[0] = I2C_ARBITRATION_LOST;
LPC_I2C0->CONCLR = I2CONCLR_SIC;
break;
}
return;
}
/*****************************************************************************
** Function name: I2C_IRQHandler
**
** Descriptions: I2C interrupt handler, deal with master mode only.
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void I2C1_IRQHandler(void)
{
uint8_t StatValue;
timeout[1] = 0;
/* this handler deals with master read and master write only */
StatValue = LPC_I2C1->STAT;
switch (StatValue)
{
case 0x08: /* A Start condition is issued. */
WrIndex1 = 0;
LPC_I2C1->DAT = I2CMasterBuffer[1][WrIndex1++];
LPC_I2C1->CONCLR = (I2CONCLR_SIC | I2CONCLR_STAC);
break;
case 0x10: /* A repeated started is issued */
RdIndex1 = 0;
/* Send SLA with R bit set, */
LPC_I2C1->DAT = I2CMasterBuffer[1][WrIndex1++];
LPC_I2C1->CONCLR = (I2CONCLR_SIC | I2CONCLR_STAC);
break;
case 0x18: /* Regardless, it's a ACK */
if (I2CWriteLength[1] == 1)
{
LPC_I2C1->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[1] = I2C_NO_DATA;
}
else
{
LPC_I2C1->DAT = I2CMasterBuffer[1][WrIndex1++];
}
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
case 0x28: /* Data byte has been transmitted, regardless ACK or NACK */
if (WrIndex1 < I2CWriteLength[1])
{
LPC_I2C1->DAT = I2CMasterBuffer[1][WrIndex1++]; /* this should be the last one */
}
else
{
if (I2CReadLength[1] != 0)
{
LPC_I2C1->CONSET = I2CONSET_STA; /* Set Repeated-start flag */
}
else
{
LPC_I2C1->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[1] = I2C_OK;
}
}
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
case 0x30:
LPC_I2C1->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[1] = I2C_NACK_ON_DATA;
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
case 0x40: /* Master Receive, SLA_R has been sent */
if ((RdIndex1 + 1) < I2CReadLength[1])
{
/* Will go to State 0x50 */
LPC_I2C1->CONSET = I2CONSET_AA; /* assert ACK after data is received */
}
else
{
/* Will go to State 0x58 */
LPC_I2C1->CONCLR = I2CONCLR_AAC; /* assert NACK after data is received */
}
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
case 0x50: /* Data byte has been received, regardless following ACK or NACK */
I2CSlaveBuffer[1][RdIndex1++] = LPC_I2C1->DAT;
if ((RdIndex1 + 1) < I2CReadLength[1])
{
LPC_I2C1->CONSET = I2CONSET_AA; /* assert ACK after data is received */
}
else
{
LPC_I2C1->CONCLR = I2CONCLR_AAC; /* assert NACK on last byte */
}
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
case 0x58:
I2CSlaveBuffer[1][RdIndex1++] = LPC_I2C1->DAT;
I2CMasterState[1] = I2C_OK;
LPC_I2C1->CONSET = I2CONSET_STO; /* Set Stop flag */
LPC_I2C1->CONCLR = I2CONCLR_SIC; /* Clear SI flag */
break;
case 0x20: /* regardless, it's a NACK */
case 0x48:
LPC_I2C1->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[1] = I2C_NACK_ON_ADDRESS;
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
case 0x38: /* Arbitration lost, in this example, we don't
deal with multiple master situation */
default:
I2CMasterState[1] = I2C_ARBITRATION_LOST;
LPC_I2C1->CONCLR = I2CONCLR_SIC;
break;
}
return;
}
/*****************************************************************************
** Function name: I2C_IRQHandler
**
** Descriptions: I2C interrupt handler, deal with master mode only.
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void I2C2_IRQHandler(void)
{
uint8_t StatValue;
timeout[2] = 0;
/* this handler deals with master read and master write only */
StatValue = LPC_I2C2->STAT;
switch (StatValue)
{
case 0x08: /* A Start condition is issued. */
WrIndex2 = 0;
LPC_I2C2->DAT = I2CMasterBuffer[2][WrIndex2++];
LPC_I2C2->CONCLR = (I2CONCLR_SIC | I2CONCLR_STAC);
break;
case 0x10: /* A repeated started is issued */
RdIndex2 = 0;
/* Send SLA with R bit set, */
LPC_I2C2->DAT = I2CMasterBuffer[2][WrIndex2++];
LPC_I2C2->CONCLR = (I2CONCLR_SIC | I2CONCLR_STAC);
break;
case 0x18: /* Regardless, it's a ACK */
if (I2CWriteLength[2] == 1)
{
LPC_I2C2->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[2] = I2C_NO_DATA;
}
else
{
LPC_I2C2->DAT = I2CMasterBuffer[2][WrIndex2++];
}
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
case 0x28: /* Data byte has been transmitted, regardless ACK or NACK */
if (WrIndex2 < I2CWriteLength[2])
{
LPC_I2C2->DAT = I2CMasterBuffer[2][WrIndex2++]; /* this should be the last one */
}
else
{
if (I2CReadLength[2] != 0)
{
LPC_I2C2->CONSET = I2CONSET_STA; /* Set Repeated-start flag */
}
else
{
LPC_I2C2->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[2] = I2C_OK;
}
}
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
case 0x30:
LPC_I2C2->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[2] = I2C_NACK_ON_DATA;
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
case 0x40: /* Master Receive, SLA_R has been sent */
if ((RdIndex2 + 1) < I2CReadLength[2])
{
/* Will go to State 0x50 */
LPC_I2C2->CONSET = I2CONSET_AA; /* assert ACK after data is received */
}
else
{
/* Will go to State 0x58 */
LPC_I2C2->CONCLR = I2CONCLR_AAC; /* assert NACK after data is received */
}
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
case 0x50: /* Data byte has been received, regardless following ACK or NACK */
I2CSlaveBuffer[2][RdIndex2++] = LPC_I2C2->DAT;
if ((RdIndex2 + 1) < I2CReadLength[2])
{
LPC_I2C2->CONSET = I2CONSET_AA; /* assert ACK after data is received */
}
else
{
LPC_I2C2->CONCLR = I2CONCLR_AAC; /* assert NACK on last byte */
}
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
case 0x58:
I2CSlaveBuffer[2][RdIndex2++] = LPC_I2C2->DAT;
I2CMasterState[2] = I2C_OK;
LPC_I2C2->CONSET = I2CONSET_STO; /* Set Stop flag */
LPC_I2C2->CONCLR = I2CONCLR_SIC; /* Clear SI flag */
break;
case 0x20: /* regardless, it's a NACK */
case 0x48:
LPC_I2C2->CONSET = I2CONSET_STO; /* Set Stop flag */
I2CMasterState[2] = I2C_NACK_ON_ADDRESS;
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
case 0x38: /* Arbitration lost, in this example, we don't
deal with multiple master situation */
default:
I2CMasterState[2] = I2C_ARBITRATION_LOST;
LPC_I2C2->CONCLR = I2CONCLR_SIC;
break;
}
return;
}
/*****************************************************************************
** Function name: I2CStart
**
** Descriptions: Create I2C start condition, a timeout
** value is set if the I2C never gets started,
** and timed out. It's a fatal error.
**
** parameters: None
** Returned value: true or false, return false if timed out
**
*****************************************************************************/
uint32_t I2CStart(uint32_t portNum)
{
uint32_t retVal = FALSE;
timeout[portNum] = 0;
/*--- Issue a start condition ---*/
LPC_I2C[portNum]->CONSET = I2CONSET_STA; /* Set Start flag */
/*--- Wait until START transmitted ---*/
while(1)
{
if (I2CMasterState[portNum] == I2C_STARTED)
{
retVal = TRUE;
break;
}
if (timeout[portNum] >= MAX_TIMEOUT)
{
retVal = FALSE;
break;
}
timeout[portNum]++;
}
return(retVal);
}
/*****************************************************************************
** Function name: I2CStop
**
** Descriptions: Set the I2C stop condition, if the routine
** never exit, it's a fatal bus error.
**
** parameters: None
** Returned value: true or never return
**
*****************************************************************************/
uint32_t I2CStop(uint32_t portNum)
{
LPC_I2C[portNum]->CONSET = I2CONSET_STO; /* Set Stop flag */
LPC_I2C[portNum]->CONCLR = I2CONCLR_SIC; /* Clear SI flag */
/*--- Wait for STOP detected ---*/
while(LPC_I2C[portNum]->CONSET & I2CONSET_STO);
return TRUE;
}
/*****************************************************************************
** Function name: I2CInit
**
** Descriptions: Initialize I2C controller as a master
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void I2C0Init(void)
{
LPC_SC->PCONP |= (1 << 7);
/* set PIO0.27 and PIO0.28 to I2C0 SDA and SCL */
/* function to 01 on both SDA and SCL. */
LPC_PINCON->PINSEL1 &= ~((0x03<<22)|(0x03<<24));
LPC_PINCON->PINSEL1 |= ((0x01<<22)|(0x01<<24));
/*--- Clear flags ---*/
LPC_I2C0->CONCLR = I2CONCLR_AAC | I2CONCLR_SIC | I2CONCLR_STAC | I2CONCLR_I2ENC;
/*--- Reset registers ---*/
#if FAST_MODE_PLUS
LPC_PINCON->I2CPADCFG |= ((0x1<<0)|(0x1<<2));
LPC_I2C0->SCLL = I2SCLL_HS_SCLL;
LPC_I2C0->SCLH = I2SCLH_HS_SCLH;
#else
LPC_PINCON->I2CPADCFG &= ~((0x1<<0)|(0x1<<2));
LPC_I2C0->SCLL = I2SCLL_SCLL;
LPC_I2C0->SCLH = I2SCLH_SCLH;
#endif
/* Install interrupt handler */
NVIC_EnableIRQ(I2C0_IRQn);
LPC_I2C0->CONSET = I2CONSET_I2EN;
return;
}
/*****************************************************************************
** Function name: I2C1Init
**
** Descriptions: Initialize I2C controller as a master
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void I2C1Init(void)
{
LPC_SC->PCONP |= (1 << 19);
#if 0
/* set PIO0.0 and PIO0.1 to I2C1 SDA and SCL */
/* function to 11 on both SDA and SCL. */
LPC_PINCON->PINSEL0 &= ~((0x3<<0)|(0x3<<2));
LPC_PINCON->PINSEL0 |= ((0x3<<0)|(0x3<<2));
LPC_PINCON->PINMODE0 &= ~((0x3<<0)|(0x3<<2));
LPC_PINCON->PINMODE0 |= ((0x2<<0)|(0x2<<2)); /* No pull-up no pull-down */
LPC_PINCON->PINMODE_OD0 |= ((0x01<<0)|(0x1<<1)); /* Open drain */
#endif
#if 1
/* set PIO0.19 and PIO0.20 to I2C1 SDA and SCL */
/* function to 11 on both SDA and SCL. */
LPC_PINCON->PINSEL1 &= ~((0x3<<6)|(0x3<<8));
LPC_PINCON->PINSEL1 |= ((0x3<<6)|(0x3<<8));
LPC_PINCON->PINMODE1 &= ~((0x3<<6)|(0x3<<8));
LPC_PINCON->PINMODE1 |= ((0x2<<6)|(0x2<<8)); /* No pull-up no pull-down */
LPC_PINCON->PINMODE_OD0 |= ((0x1<<19)|(0x1<<20));
#endif
/*--- Clear flags ---*/
LPC_I2C1->CONCLR = I2CONCLR_AAC | I2CONCLR_SIC | I2CONCLR_STAC | I2CONCLR_I2ENC;
/*--- Reset registers ---*/
LPC_I2C1->SCLL = I2SCLL_SCLL;
LPC_I2C1->SCLH = I2SCLH_SCLH;
/* Install interrupt handler */
NVIC_EnableIRQ(I2C1_IRQn);
LPC_I2C1->CONSET = I2CONSET_I2EN;
return;
}
/*****************************************************************************
** Function name: I2C2Init
**
** Descriptions: Initialize I2C controller as a master
**
** parameters: None
** Returned value: None
**
*****************************************************************************/
void I2C2Init(void)
{
LPC_SC->PCONP |= (1 << 26);
/* set PIO0.10 and PIO0.11 to I2C2 SDA and SCL */
/* function to 10 on both SDA and SCL. */
LPC_PINCON->PINSEL0 &= ~((0x03<<20)|(0x03<<22));
LPC_PINCON->PINSEL0 |= ((0x02<<20)|(0x02<<22));
LPC_PINCON->PINMODE0 &= ~((0x03<<20)|(0x03<<22));
LPC_PINCON->PINMODE0 |= ((0x02<<20)|(0x2<<22)); /* No pull-up no pull-down */
LPC_PINCON->PINMODE_OD0 |= ((0x01<<10)|(0x1<<11));
/*--- Clear flags ---*/
LPC_I2C2->CONCLR = I2CONCLR_AAC | I2CONCLR_SIC | I2CONCLR_STAC | I2CONCLR_I2ENC;
/*--- Reset registers ---*/
LPC_I2C2->SCLL = I2SCLL_SCLL;
LPC_I2C2->SCLH = I2SCLH_SCLH;
/* Install interrupt handler */
NVIC_EnableIRQ(I2C2_IRQn);
LPC_I2C2->CONSET = I2CONSET_I2EN;
return;
}
/*****************************************************************************
** Function name: I2CEngine
**
** Descriptions: The routine to complete a I2C transaction
** from start to stop. All the intermitten
** steps are handled in the interrupt handler.
** Before this routine is called, the read
** length, write length, I2C master buffer,
** and I2C command fields need to be filled.
** see i2cmst.c for more details.
**
** parameters: I2C port number
** Returned value: master state of current I2C port.
**
*****************************************************************************/
uint32_t I2CEngine(uint32_t portNum)
{
/*--- Issue a start condition ---*/
LPC_I2C[portNum]->CONSET = I2CONSET_STA; /* Set Start flag */
I2CMasterState[portNum] = I2C_BUSY;
while (I2CMasterState[portNum] == I2C_BUSY)
{
if (timeout[portNum] >= MAX_TIMEOUT)
{
I2CMasterState[portNum] = I2C_TIME_OUT;
break;
}
timeout[portNum]++;
}
LPC_I2C[portNum]->CONCLR = I2CONCLR_STAC;
return (I2CMasterState[portNum]);
}
/******************************************************************************
** End Of File
******************************************************************************/
MPU6050功能
void mpu6050BurstRead(uint8_t startRegAdd, uint8_t length, uint8_t *data) {
// Clear buffers
uint32_t i;
for (i = 0; i < BUFSIZE; i++) {
I2CMasterBuffer[I2C_PORT][i] = 0x00;
I2CSlaveBuffer[I2C_PORT][i] = 0x00;
}
I2CWriteLength[I2C_PORT] = 2;
I2CReadLength[I2C_PORT] = 0;
I2CMasterBuffer[I2C_PORT][0] = MPU6050_ADDRESS;
I2CMasterBuffer[I2C_PORT][1] = startRegAdd;
I2CEngine(I2C_PORT);
for (i = 0; i < BUFSIZE; i++) {
I2CMasterBuffer[I2C_PORT][i] = 0x00;
I2CSlaveBuffer[I2C_PORT][i] = 0x00;
}
I2CWriteLength[I2C_PORT] = 1;
I2CReadLength[I2C_PORT] = length;
I2CMasterBuffer[I2C_PORT][0] = MPU6050_ADDRESS|MPU6050_READ;
I2CEngine(I2C_PORT);
memcpy(data,I2CSlaveBuffer,length);
}
void mpu6050Write(uint8_t regAdd,uint8_t regValue) {
// Clear buffers
uint32_t i;
for (i = 0; i < BUFSIZE; i++) {
I2CMasterBuffer[I2C_PORT][i] = 0x00;
I2CSlaveBuffer[I2C_PORT][i] = 0x00;
}
I2CWriteLength[I2C_PORT] = 3;
I2CReadLength[I2C_PORT] = 0;
I2CMasterBuffer[I2C_PORT][0] = MPU6050_ADDRESS;
I2CMasterBuffer[I2C_PORT][1] = regAdd;
I2CMasterBuffer[I2C_PORT][2] = regValue;
I2CEngine(I2C_PORT);
}
什麼？我們沒有硬件，沒有調試器，沒有範圍，沒有環境，沒有代碼。另外，'我嘗試了很多可能的方式' - 什麼方式？你已經做了一些調試，但不會告訴我們你做了什麼？你可能很幸運，之前遇到這個問題的人會想出一個答案，但除此之外，我們不能幫助你提供很少的信息。 – 2014-10-18 08:54:56
對不起馬丁詹姆斯..，我已經編輯該帖子。 Plz看一次 – Nataraj 2014-10-18 09:28:06